# Klipper

**URL:** http://forum.3dprintbeginner.com/c/3d-printer-firmware/klipper/29.md

[Latest](http://forum.3dprintbeginner.com/latest.md) · [Categories](http://forum.3dprintbeginner.com/categories.md) · [Tags](http://forum.3dprintbeginner.com/tags.md)

---

## [About the Klipper category](http://forum.3dprintbeginner.com/t/about-the-klipper-category/35)

<div class="topic-metadata">

**Author:** [@3DPrintBeginner](http://forum.3dprintbeginner.com/u/3DPrintBeginner)\
**Replies:** 0

</div>

General discussions about Klipper Firmware.

---

## [Replacing stepper motors with a pitch of 1.8\* with motors with a pitch of 0.9\* Creality k1 max](http://forum.3dprintbeginner.com/t/replacing-stepper-motors-with-a-pitch-of-1-8-with-motors-with-a-pitch-of-0-9-creality-k1-max/2569)

<div class="topic-metadata">

**Author:** [@raketa\_09985](http://forum.3dprintbeginner.com/u/raketa_09985)\
**Replies:** 0\
**Last updated:** [September 12, 2025, 4:42pm UTC](http://forum.3dprintbeginner.com/t/replacing-stepper-motors-with-a-pitch-of-1-8-with-motors-with-a-pitch-of-0-9-creality-k1-max/2569 "2025-09-12T16:42:38Z")

</div>

On my Creality K1 Max, the stepper motors (BJ42D29-30V09 with a 1.8° step) on the X and Y axes have failed. I couldn’t find identical motors for replacement, so I had to install different ones (LDO-42STH60-2004MAC(S55) …

---

## [Creality CR-10 Smart Klipper Firmware with internal Creality Box](http://forum.3dprintbeginner.com/t/creality-cr-10-smart-klipper-firmware-with-internal-creality-box/124)

<div class="topic-metadata">

**Author:** [@3DPrintBeginner](http://forum.3dprintbeginner.com/u/3DPrintBeginner)\
**Replies:** 32\
**Last updated:** [August 20, 2024, 11:35am UTC](http://forum.3dprintbeginner.com/t/creality-cr-10-smart-klipper-firmware-with-internal-creality-box/124 "2024-08-20T11:35:38Z")

</div>

I converted the Creality CR-10 Smart to Klipper, using the internal Creality Box inside the machine. I attached the config file and the firmware build configuration. Klipper WRT can be installed with this guide: How to…

---

## [Cannot move any of my SX2 axis on Klipper](http://forum.3dprintbeginner.com/t/cannot-move-any-of-my-sx2-axis-on-klipper/1533)

<div class="topic-metadata">

**Author:** [@lone182](http://forum.3dprintbeginner.com/u/lone182)\
**Replies:** 0\
**Last updated:** [July 9, 2023, 7:03pm UTC](http://forum.3dprintbeginner.com/t/cannot-move-any-of-my-sx2-axis-on-klipper/1533 "2023-07-09T19:03:52Z")

</div>

Hello everyone, I had a problem 3 weeks ago that my Sidewinder x2 shortened the LCD, so I found klipper as a possible solution. I managed to install it with a MKS pi as a controller board. However I cannot move any axis…

---

## [Sidewinder Klipper PID Tuning Issue](http://forum.3dprintbeginner.com/t/sidewinder-klipper-pid-tuning-issue/350)

<div class="topic-metadata">

**Author:** [@Astral](http://forum.3dprintbeginner.com/u/Astral)\
**Replies:** 3\
**Last updated:** [March 31, 2022, 6:03am UTC](http://forum.3dprintbeginner.com/t/sidewinder-klipper-pid-tuning-issue/350 "2022-03-31T06:03:35Z")

</div>

I have a Sidewinder x1 printer. I use klipper. I’m doing pid tuning, but the result is different from what I did with marlin. Although my first layer bed temperature is 60 degrees, it rises to 65 degrees. The print is t…

---

## [Longer idle time when pre heating](http://forum.3dprintbeginner.com/t/longer-idle-time-when-pre-heating/225)

<div class="topic-metadata">

**Author:** [@TT3ch](http://forum.3dprintbeginner.com/u/TT3ch)\
**Replies:** 6\
**Last updated:** [March 22, 2022, 6:44pm UTC](http://forum.3dprintbeginner.com/t/longer-idle-time-when-pre-heating/225 "2022-03-22T18:44:01Z")

</div>

Running klipper with mainsail. How do I increase the idle time when preheating the bed. My bed heater is also part of my enclosure heating. However Klipper shuts it down after 10 minutes when not printing. I can’t find …

---

## [Pressure Advance in a style of Marlin K-factor](http://forum.3dprintbeginner.com/t/pressure-advance-in-a-style-of-marlin-k-factor/164)

<div class="topic-metadata">

**Author:** [@Kosmak](http://forum.3dprintbeginner.com/u/Kosmak)\
**Replies:** 0\
**Last updated:** [March 11, 2022, 11:22am UTC](http://forum.3dprintbeginner.com/t/pressure-advance-in-a-style-of-marlin-k-factor/164 "2022-03-11T11:22:31Z")

</div>

So I was trying to dial in my CF PLA Pressure Advance and stumbled upon a great script that will help anyone streamline their PA Calibration I am sure all of you are familiar with the old cube test. If not, there is a p…

---

## [CAN Toolhead Controller](http://forum.3dprintbeginner.com/t/can-toolhead-controller/84)

<div class="topic-metadata">

**Author:** [@3DPrintBeginner](http://forum.3dprintbeginner.com/u/3DPrintBeginner)\
**Replies:** 0\
**Last updated:** [February 15, 2022, 6:47am UTC](http://forum.3dprintbeginner.com/t/can-toolhead-controller/84 "2022-02-15T06:47:52Z")

</div>

This is pretty cool. Alternative to the BTT Hermit Crab toolhead board. https://www.youtube.com/watch?v=Pi5cdTiGjwY
